An Introduction to the 5G Frequency Spectrum

Posted by Peter Matthews on Aug 26, 2020 9:15:00 AM
Peter Matthews

Planning is in the works for Fifth Generation (5G) communication systems that will enable a hundred-fold increase in user data-rates – and with this increase comes a need for significant increases in bandwidth over what is currently available. Why does bandwidth follow when we ask for an increase in data rates? 

In 1948 Claude Shannon and Ralph Hartley, both researchers at Bell Labs, developed what has become known as the Shannon-Hartley Theorem. It tells us the maximum amount of error-free digital data that can be transmitted over a channel of a given bandwidth in the presence of noise:

shannon1

Where:

C = Channel capacity in bits/second

M = Number of channels (e.g. the MIMO order)

B = Bandwidth in hertz

S = transmit power, in watts

N = noise on channel, in watts

S/N = signal to noise ratio

To increase channel capacity (data rates) we can increase bandwidth, increase the number of channels, increase transmit power (S) and decrease the noise on the channel (N).

In order to achieve the data rates targeted by 5G systems, innovation is taking place on all of these fronts, but the factor in the equation we will discuss in this article is B, the channel bandwidth.

Questions of bandwidth come naturally to looking at available spectrum – both because of questions of how much bandwidth is available in a given part of the spectrum, and because as frequency increases a given percent bandwidth gives us a greater share of spectrum.

 

LTE Spectrum

The 3GPP document TS 36.101 defines the LTE FDD and TDD bands. Version 14.5 defines 52 bands for 4G LTE spectrum, ranging in frequency from 450 MHz (Band 31) to 5900 MHz (Band 47).

The spectrum outlined in the standard is intended to support six channel bandwidths: 1.4 MHz, 3 MHz, 5 MHz, 10 MHz, 15 MHz, and 20 MHz. To reach higher bandwidths (and thus higher data rates) a technique called Channel Aggregation (CA) is used to stitch together non-contiguous bands. TS 36.101 defines the bands available for CA.

Globally, there are more than 1,000 band combinations supported. An overview of common frequency ranges in operation today can be seen below.

 

lte_map

 

In the U.S., the major carriers have centered their activity around 11 bands. This table shows key LTE bands in the U.S.

Band AT&T Verizon Wireless T-Mobile Sprint
Band 2, FDD UL, 1850 – 1910MHz  
Band 2, FDD DL, 1930 – 1990MHz  
Band 4, FDD UL, 1710 – 1755MHz  
Band 4, FDD DL, 2110 – 2155MHz  
Band 5, FDD UL, 824 – 849MHz      
Band 5, FDD DL, 869 – 894MHz      
Band 12, FDD UL, 699 – 716MHz    
Band 12, FDD DL, 729 – 746MHz    
Band 13, FDD DL, 746 – 756MHz      
Band 13, FDD UL, 777 – 787MHz      
Band 17, FDD UL, 704 – 716MHz      
Band 17, FDD DL, 734 – 746MHz      
Band 25, FDD UL, 1850 – 1915MHz      
Band 25, FDD DL, 1930 – 1995MHz      
Band 26, FDD UL, 814 – 849MHz      
Band 26, FDD DL, 859 – 894MHz      
Band 41, TDD, 2496 – 2690MHz      
Band 66, FDD UL, 1710 – 1780MHz      
Band 66, FDD DL, 2110 – 2200MHz      
Band 71, FDD DL, 617 – 652MHz      
Band 71, FDD UL, 663 – 698MHz      

Contiguous bandwidth of 100 MHz is hard to find in the LTE spectrum landscape. Given that the peak data rate goal for 5G is 20 Gbps (and the goal for LTE was 1 Gbps) that 20x increase in channel capacity has to come from somewhere. Now as we mentioned above innovation is happening to address all of the variables in the Shannon Hartley model to get us there. A key innovation at the heart of 5G is utilizing new spectrum where increases in bandwidth are easier to come by.

 

5G Spectrum

3GPP has been working on 5G for some time, and a major differentiator is the maximum bandwidths allocated to each channel. Where in 4G we had 20 MHz maximum (and CA to stitch together more), in 5G we will have caps of 100 MHz below 6 GHz and 400 MHz above 6 GHz. Below 6 GHz 400 MHz will be achieved through CA (e.g. 4x 100 MHz). In moving from 20 MHz to 400 MHz max, 3GPP have built the potential for a 20x increase in channel capacity right into the spectrum planning.

Here are some of the candidate 5G bands:

Region Flow Fhigh Band
Korea 3400 MHz 3700 MHz  
26.5 GHz 29.5 GHz  
EU 2570 MHz 2620 MHz 38
3400 MHz 3800 MHz 42+43
24.25 GHz 27.35 GHz  
31.8 GHz 33.4 GHz  
40.5 GHz 43.5 GHz  
Japan 2496 2690 41
3400 3600 42
3600 4200  
4400 4900  
27.5 GHz 29.5 GHz  
US 2496 2690 41
3550 3700 48
27.5 GHz 28.35 GHz  
37 GHz 38.6 GHz  
38.6 GHz 40 GHz  
64 GHz 71 GHz  
China 2300 2400 40
2555 2655 41B
3300 3600  
3400 3600 42
4400 4500  
4800 4990  

With these new bands come groups of use-cases based on frequency. We can look at use cases that fall into frequencies below 1 GHz, between 1 GHz and 6 GHz and those at the cm-wave and mm-wave frequencies.

Frequencies below 1 GHz in the UHF perform well in applications that require long range and high data rates – these are the frequencies we are used to seeing in Macro base station applications. Moving forward to 5G they will be leveraged for lower data rate and narrow band applications (such as already used in 4G IoT applications) and are looked at for the ‘massive Machine to Machine Type Communications’ (mMTC).

From 1 GHz to 6 GHz we encounter the familiar LTE bands. This region is being looked at for use cases that need of the order of 100 MHz of bandwidth, with the 2.5 GHz Band 41 and 3.5 GHz (42+43) regarded as candidates for 5G enhanced Mobile Broadband (eMBB) applications.

Starting at 28 GHz we find the cm-wave and mmWave frequencies that are being utilized in Fixed Wireless Access (FWA) applications. It is these frequencies that are being deployed first, with demonstrations already having happened at the Winter Olympics in Korea in 2018.

The high end of the spectrum offers the most dramatic increase in available bandwidths, allowing designers to push Shannon-Hartley to incredible speeds.

To address the <6 GHz (low and mid band) and mmWave (high band) use-cases 3GPP TS 38.101 defines the following frequency ranges:

  • FR1 = 410 MHz – 7125 MHz
  • FR2 = 24.25 GHz – 52.6 GHz

Currently within these ranges, a handful of bands are being used.

Within FR1:

3GPP FR1 Bands

Low (GHz)

High (GHz)

n77

3.3

4.2

n78

3.3

3.8

n79

4.4

5

 

Within FR2:

3GPP FR2 Bands

Low (GHz)

High (GHz)

n258, 26GHz

24.25

27.5

n257, 28GHz

26.5

29.5

n261, 28GHz*

27.5

28.35

n260, 39GHz

37

40

(*n261 is a sub-band of n257)

 

Learn more about the 5G Frequency Spectrum and the options available for implementing RF filtering at mmWave frequencies by downloading our white paper, RF Filtering for 5G Millimeter Wave Applications. 

Download the Paper

 

Topics: 5G, RF and Microwave

Insights Into Precision Passive Devices

Knowles Precision Devices is a premier global source for Capacitors, RF Filters, EMI Filters, Resonators, non-magnetic components and advanced dielectric materials. An umbrella for the brands of Compex, DLI, Johanson MFG, Novacap, Syfer and Voltronics, Knowles Precision Devices serves a variety of markets including military, aerospace/avionics, medical equipment, implantable devices, EMI and connector filtering, oil exploration, instrumentation, industrial electronics, automotive, telecoms and data networks.

This Blog will provide insights into:

  • Filters for 5G and mmWave
  • Capacitors for High Voltage
  • Capacitors for High Reliability

and much more. Subscribe below to stay informed.

Subscribe Here!

Recent Posts